Service of the Infiniti QX4 since 1996 of release
1. Introduction
2. Maintenance instruction
3. Routine maintenance
4. Engine
5. Cooling system and heating
6. Feed and control systems
7. Systems of start and charge
8. Transmission line
9. Brake system
10. Suspension bracket and steering
10.1. Specifications
10.2. Assessment of the general condition of components of a suspension bracket and steering of the car
10.3. Check of a state and replacement of spherical support of a forward suspension bracket
10.4. Check of a condition of steering drafts
10.5. Removal and installation of the cross lever of a forward suspension bracket
10.6. Adjustment of a pretightness of stupichny bearings of forward wheels
10.7. Removal, check of a state and installation of screw springs and rack-mount assemblies of a forward suspension bracket
10.8. Removal and installation of stupichny assembly and rotary fist
10.9. Removal, check of a state and installation of the forward stabilizer of cross stability
10:10. Replacement of stupichny bearings
10:11. Check of a condition of shock-absorbers and springs of a back suspension bracket
10:12. Removal and installation of components and assembly of a back suspension bracket
10:13. Removal, check of a state and installation of levers of a back suspension bracket
10:14. Removal, check of a state and installation of screw springs of a back suspension bracket
10:15. Removal and installation of shock-absorbers of a back suspension bracket
10:16. Removal and installation of the back stabilizer of cross stability
10:17. Removal, check of a state and installation of a cross jet bar of a back suspension bracket
10:18. Pumping of a hydraulic path of the steering drive
10:19. Checks and adjustments of a steering wheel
10:20. Check of effort of resistance to sliding of a lath of the steering mechanism
10:21. Adjustment of torque of a provorachivaniye of the leading gear wheel of the steering mechanism
10:22. Check of hydraulic pressure of GUR
10:23. Adjustment of effort of a tension of a belt of the drive of the steering pump
10:24. Removal and installation of reduktorny assembly
10:25. Removal and installation of assembly of the steering mechanism
10:26. Removal and installation of the steering pump
10:27. Removal and installation of a steering wheel
10:28. Removal and installation of assembly of the combined understeering switches
10:29. Removal and installation of the lock of ignition / blocking of a steering column
10:30. Removal, check of a state and installation of a steering column
10:31. Angles of installation of forward wheels
11. Body
12. Electric equipment
 






5d7aa768






10-7-snyatie-proverka-sostoyaniya-i-ustanovka-vintovykh-pruzhin-i.html

10.7. Removal, check of a state and installation of screw springs and rack-mount assemblies of a forward suspension bracket

Before removal of components check a condition of shock-absorbers and screw springs on the car standing on the earth. Serially press on each of car corners — serviceable shock-absorbers provide return of a corner at an otpuskaniye for one muscleman a body. For assessment of a condition of screw springs several times rock the car for shrinkage of components, then check height of landing of a body (nominal rates — see the illustration Assessment of a Condition of Screw Springs) — the sunk springs are not subject to recovery repair and have to be replaced.


Assessment of a condition of screw springs

Hf — 815 mm

Hr — 855/846 mm (see Specifications)


Removal

 PERFORMANCE ORDER

    The car also establish to Poddomkratta it on props (see the illustration Scheme of an Institution of Props for fixing of the car in the lifted situation). Remove the corresponding forward wheel. Disconnect a bar of the stabilizer of cross stability from a rack. Prop up I will lower the cross lever of a suspension bracket.
    Mark the provision of a rack of rather rotary fist, then give fixing nuts and bolts of the lower support of rack-mount assembly. Release nuts of fastening of the top support of a rack to a car body — do not turn off a nut of fastening of a rod of the shock-absorber.
    Remove assembly of a rack with a screw spring from the car, transfer it to a workbench and clamp in a vice with soft sponges.
    Slightly weaken a shock-absorber rod nut, then squeeze a screw spring by means of the special tool and finally turn off a nut.
    The final otdavaniye of a nut of a rod of the shock-absorber is made after compression of a screw spring.
    Remove a screw spring from rack-mount assembly.


Check

 PERFORMANCE ORDER

    Estimate smoothness of the courses of compression and stretching are resistant.
    Examine assembly on existence of signs of development of leaks.
    Make sure of absence on the piston of cracks, deformations and other mechanical damages. The faulty rack is subject to replacement.


Installation

 PERFORMANCE ORDER

    Put on rack-mount assembly a screw spring (a flat end face up) and make sure of hit of the lower end face of its bar in reciprocal deepening in a saddle.
    Track that the top saddle of a spring was developed by an U-shaped cut to DP of the car and on one line with points of fastening are resistant to a rotary fist.
    Further installation is made as it should be, the return to an order of dismantle of components. Track that all fixture was tightened with the required effort.


"on the page back
10.6. Adjustment of a pretightness of stupichny bearings of forward wheels
on the following page"
10.8. Removal and installation of stupichny assembly and rotary fist