Service of the Infiniti QX4 since 1996 of release
1. Introduction
2. Maintenance instruction
3. Routine maintenance
4. Engine
5. Cooling system and heating
6. Feed and control systems
7. Systems of start and charge
8. Transmission line
9. Brake system
10. Suspension bracket and steering
10.1. Specifications
10.2. Assessment of the general condition of components of a suspension bracket and steering of the car
10.3. Check of a state and replacement of spherical support of a forward suspension bracket
10.4. Check of a condition of steering drafts
10.5. Removal and installation of the cross lever of a forward suspension bracket
10.6. Adjustment of a pretightness of stupichny bearings of forward wheels
10.7. Removal, check of a state and installation of screw springs and rack-mount assemblies of a forward suspension bracket
10.8. Removal and installation of stupichny assembly and rotary fist
10.9. Removal, check of a state and installation of the forward stabilizer of cross stability
10:10. Replacement of stupichny bearings
10:11. Check of a condition of shock-absorbers and springs of a back suspension bracket
10:12. Removal and installation of components and assembly of a back suspension bracket
10:13. Removal, check of a state and installation of levers of a back suspension bracket
10:14. Removal, check of a state and installation of screw springs of a back suspension bracket
10:15. Removal and installation of shock-absorbers of a back suspension bracket
10:16. Removal and installation of the back stabilizer of cross stability
10:17. Removal, check of a state and installation of a cross jet bar of a back suspension bracket
10:18. Pumping of a hydraulic path of the steering drive
10:19. Checks and adjustments of a steering wheel
10:20. Check of effort of resistance to sliding of a lath of the steering mechanism
10:21. Adjustment of torque of a provorachivaniye of the leading gear wheel of the steering mechanism
10:22. Check of hydraulic pressure of GUR
10:23. Adjustment of effort of a tension of a belt of the drive of the steering pump
10:24. Removal and installation of reduktorny assembly
10:25. Removal and installation of assembly of the steering mechanism
10:26. Removal and installation of the steering pump
10:27. Removal and installation of a steering wheel
10:28. Removal and installation of assembly of the combined understeering switches
10:29. Removal and installation of the lock of ignition / blocking of a steering column
10:30. Removal, check of a state and installation of a steering column
10:31. Angles of installation of forward wheels
11. Body
12. Electric equipment
 






5d7aa768






10-12-snyatie-i-ustanovka-komponentov-i-sborki-zadnejj-podveski.html

10:12. Removal and installation of components and assembly of a back suspension bracket

The general design of a back suspension bracket — cm. illustration Design of a Back Suspension Bracket.


Details of installation of elements of a back suspension bracket on the car


 PERFORMANCE ORDER

    Before starting an otpuskaniye of fixture of components, prop up assembly of the back bridge a cart jack, having enclosed the wooden block on its head. Having hung out a suspension bracket, disconnect hydraulic brake lines and cables of the drive of the parking brake from brake boards.

In order to avoid a rounding off of shlits of cap nipple nuts use a special cap key with a cutting head. Remove wheel ABS sensors from a suspension bracket and take them aside together with the connected electrical wiring.

    Release fixture of collars of fastening of a bar of the back stabilizer of cross resistance to a body. Give fixture and disconnect the top and lower levers of a suspension bracket from the car bottom. Disconnect the driveshaft from the main transfer of the back bridge. Give nuts of fastening of the top support of back shock-absorbers. In case of need remove the components needing replacement from assembly. Installation is made upside-down.

Final tightening of fixture of the elements equipped with rubber plugs is made in the unloaded state with the wheels lowered on the earth.



"on the page back
10:11. Check of a condition of shock-absorbers and springs of a back suspension bracket
on the following page"
10:13. Removal, check of a state and installation of levers of a back suspension bracket