4.1. Specifications

Separate parameters are specified also in the text of the Head and in case of obligation of their performance are highlighted in bold type.

Designation

VG33E

Type

Petrol, 4-stroke, 6-cylinder (  V6 x 60 °), DOHC

Arrangement

Forward, longitudinal

GRM drive

Zubchatoremenny transfer

The number of valves on the cylinder

4

Working volume of cylinders, cm ³

3275

The developed power, h.p.

168 (125) at 4800 rpm

Torque, Nanometer

266 at 2800 rpm

Diameter of cylinders, mm

91.5

Course of pistons, mm

83.0

Ignition order (see the illustration Scheme of an Arrangement of Cylinders)

1-2-3-4-5-6

Compression pressure in cylinders, kgf/cm ²

Nominal rate

12.1

Minimum admissible value

9.0

The maximum admissible difference between cylinders

1.0

Extent of compression

8.9:1

Power supply system

The distributed consecutive injection (SFI)

Pressure of oil, kgf/cm ²

On single turns

0.6

At turns of 2000 in a minute

4.2 — 4.6

Gap between teeths of external and internal gear wheels, mm

Extreme admissible working value

0.180

Gap between an external gear wheel and a pump housing, mm

Nominal rate

0.114 — 0.200

Axial side play of gear wheels in the case, mm

External gear wheel

0.050 — 0.109

Internal gear wheel

0.050 — 0.090

Gap of landing of a ledge of an internal gear wheel in a nest of the case, mm

0.045 — 0.091

Adjusting height of a head, mm (see Removal, check of a state and installation of a head of cylinders)

106.80 — 107.20

Extreme admissible size of not planeness, mm

0.10

Extreme admissible total depth of a pro-point (block + head), mm

0.20

Tilt angle of a working facet, hail

45

Width of a working facet, mm

Inlet valves

1.75

Final valves

1.70

Diameter of a landing nest, mm

Inlet valves

44.500 — 44.516

Final valves

37.500 — 37.516

Diameter of a landing nest, mm

Inlet valves

11.175 — 11.196

Final valves

12.175 — 12.196

Internal diameter, mm

Inlet valves

7.000 — 7.018

Final valves

8.000 — 8.011

Adjusting height of a vystupaniye *, mm

13.20 — 13.40

Gaps of landing of cores of valves, mm

Inlet valves

0.020 — 0.053

Final valves

0.040 — 0.049

* It is measured from the top cut of the plug to a surface of a saddle of an external spring at the removed adjusting washer (see Dismantling and check of a condition of a head of cylinders and components of the valvate mechanism).

Tilt angle of a working facet, hail

45 °15' — 45 °45'

Diameter of a plate, mm

41.95 — 42.25

Minimum admissible width of a cylindrical part of a plate, mm

0.50

Minimum admissible length, mm

125.30

Diameter of a core, mm

6.965 — 6.980

Maximum admissible depth of a face pro-point of a shaft, mm

0.20

Tilt angle of a working facet, hail

45 °15' — 45 °45'

Diameter of a plate, mm

35.00 — 35.20

Minimum admissible width of a cylindrical part of a plate, mm

0.50

Minimum admissible length, mm

124.20

Diameter of a core, mm

7.962 — 7.970

Maximum admissible depth of a face pro-point of a shaft, mm

0.20

Free length, mm

Internal spring

44.10

External spring

51.20

The extreme admissible size of violation of a tortsovka, mm (see Dismantling and check of a condition of a head of cylinders and components of the valvate mechanism)

Internal spring

1.90

External spring

2.20

Effort of compression, kgf/mm

Internal spring

26/25

External spring

74.7/30

Diameter of a landing nest, mm

16.000 — 16.013

Diameter of a pusher, mm

15.947 — 145.957

Landing gap, mm

0.043 — 0.066

Diameter of bearings, mm

Under a neck "And"

47.000 — 47.025

Under a neck "In"

42.500 — 42.525

Under a neck "With"

48.000 — 48.025

Diameter of necks, mm

Neck "And"

46.920 — 46.94

Neck "In"

42.420 — 42.440

Neck "With"

47.920 — 47.940

Size of an axial side play of a shaft, mm

0.30 — 0.60

Extreme admissible size of a radial beating, mm

0.10

Height of cams, mm

38.943 — 39.133

Working gaps in bearings, mm

0.060

Extreme admissible size of a radial beating of a cogwheel, mm

0.10

Diameter of cylinders, mm

Except cylinders No. No. 3 and 4

Dimensional group 1

91.500 — 91.510

Dimensional group 2

91.511 — 91.520

Dimensional group 3

91.521 — 91.530

Cylinders No. No. 3 and 4

Dimensional group 1

91.500 — 91.505

Dimensional group 2

91.506 — 91.510

Dimensional group 3

91.511 — 91.515

Dimensional group 4

91.516 — 91.520

Dimensional group 5

91.521 — 91.525

Dimensional group 6

91.526 — 91.530

Extreme admissible size of conicity of cylinders, mm

0.015

Extreme admissible size of ovality of cylinders, mm

0.015

Minimum admissible height, mm

Information is not provided

Extreme admissible size of not planeness, mm

0.10

Extreme admissible total depth of a pro-point (block + head), mm

0.20

Size of an axial side play, mm

Nominal rate

0.05 — 0.17

Extreme admissible value

0.30

Size of a radial beating, mm

Nominal rate

0.025

Extreme admissible value

0.10

Diameter of necks, mm

Dimensional 0 group

62.967 — 62.975

Dimensional 1 group

62.959 — 62.967

Dimensional 2 group

62.951 — 62.959

Extreme admissible size of conicity of necks, mm

0.005

Extreme admissible size of ovality of necks, mm

0.005

Working gaps in bearings, mm

Nominal rate

0.028 — 0.056

Extreme admissible value

0.090

Diameter of necks, mm

49.955 — 49.974

Extreme admissible size of conicity of necks, mm

0.005

Extreme admissible size of ovality of necks, mm

0.005

Working gaps in bearings, mm

Nominal rate

0.015 — 0.054

Extreme admissible value

0.090

Diameters of nests of heads, mm

Top head

20.982 — 20.994

Lower head

53.000 — 53.013

Distance between centers nests, mm

154.10 — 154.20

The extreme admissible size of a bend is at 100 mm of length, mm

0.15

The extreme admissible size of twisting is at 100 mm of length, mm

0.30

Size of an axial side play, mm

Nominal rate

0.20 — 0.35

Extreme admissible value

0.40

Landing gaps in cylinders, mm

Except No. No. 3 and 4

0.025 — 0.045

No. No. 3 and 4

0.015 — 0.025

Diameter, mm

Except No. No. 3 and 4

Dimensional group 1

91.465 — 91.475

Dimensional group 2

91.475 — 91.485

Dimensional group 3

91.485 — 91.495

With excess on 0:25 mm

91.715 — 91.745

With excess on 0:50 mm

91.965 — 91.995

Cylinders No. No. 3 and 4

Dimensional group 2-1

91.480 — 91.185

Dimensional group 3-2

91.485 — 91.490

Dimensional group 3-3

91.490 — 91.495

Dimensional group 4-4

91.495 — 91.500

Dimensional group 4-5

91.500 — 91.505

Dimensional group 5-6

91.505 — 91.510

With excess on 0:25 mm

91.715 — 91.745

With excess on 0:50 mm

91.965 — 91.995

Diameter, mm

20.971 — 20.983

Landing in the piston, mm

0 — 0.004 (in a tightness)

Landing in a rod, mm

0.005 — 0.017

Gap in the lock, mm

The first compression

0.20 — 0.40

The second compression

0.50 — 0.69

Oil scraper

0.20 — 0.69

Side gap of landing in a flute, mm

The first compression

0.024 — 0.076

The second compression

0.030 — 0.070

Oil scraper

0.015 — 0.185

Fastening of a persistent plate of the camshaft

78 — 88

Bolt of fastening of a cogwheel of the camshaft

78 — 88

Nuts of the lower heads of rods

Stage 1

14 — 16

Stage 2

To hold on on a corner of 60 — 65 degrees

Bolt of a pulley of a bent shaft

191 — 211

Bolts of fastening of heads of cylinders (see the illustration Order of Tightening of Bolts of Fastening of Heads of Cylinders)

Stage 1

29

Stage 2

59

Stage 3

To release everything

Stage 4

29

Stage 5

To hold on on a corner of 60 — 65 degrees

Bolts of fastening of support of a suspension bracket of the power unit to the block of cylinders

43 — 55

Bolts / nut of fastening of final collectors (see the illustration Order of Tightening of Bolts of Fastening of Final Collectors)

28 — 33

Bolts of fastening of the distributor of ignition

14 — 18

Bolts of fastening of a driving disk

83 — 93

Bolts of fastening of the inlet pipeline

18 — 22

Bolts of fastening of assembly of covers of radical bearings (a tightening order — the return shown (see the illustration Order of an Otpuskaniye of Bolts of Fastening of Assembly of Covers of Radical Bearings))

90 — 100

Drain stopper of the pallet of a case

29 — 39

Bolt of fastening of a maslozaborny tube to pump assembly

16 — 17

Bolts of fastening of the oil pump to the block of cylinders

Long

22 — 29

Short

6 — 8

Bolts of fastening of a cover of the oil pump

6 — 8

Cap of the reducing valve

39 — 69

Bolts of fastening of assemblies of axes of yokes

18 — 22

Bolt / nut of a natyazhitel of a gas-distributing belt

43 — 58

Bolts of fastening of the water pump

12 — 15

Bolts / nut of fastening of the inlet pipeline (a tightening order — the return shown (see Removal and installation of the inlet pipeline))

Stage 1

4

Stage 2

8 — 10

Bolts of fastening of the pallet of a case (see the illustration Order of Tightening of Bolts of Fastening of the Pallet of a Case)

7 — 8

Bolts of fastening of the holder of a back epiploon of a bent shaft

6 — 8

Bolts of fastening of a cover of the GRM drive

3 — 5

Screws of fastening of covers of GRM

3