Service of the Infiniti QX4 since 1996 of release
1. Introduction
2. Maintenance instruction
3. Routine maintenance
4. Engine
5. Cooling system and heating
6. Feed and control systems
7. Systems of start and charge
8. Transmission line
9. Brake system
10. Suspension bracket and steering
11. Body
12. Electric equipment
12.1. Specifications
12.2. Search of causes of failures of electric equipment
12.3. Electric sockets - general information
12.4. Safety locks and fusible inserts - the general information
12.5. Chain breakers - the general information
12.6. The relay - the general information and check of serviceability of functioning
12.7. Check of serviceability of functioning and replacement of the breaker of indexes of turns / alarm system
12.8. Replacement of lamps of lighting fixtures
12.9. Check of serviceability of functioning and recovery repair of a heater of back glass
12:10. System of additional safety (SRS)
12:11. Schemes of electric connections
 












12-6-rele-obshhaya-informaciya-i-proverka-ispravnosti-funkcionirovaniya.html

12.6. The relay - the general information and check of serviceability of functioning


The scheme of an arrangement of electric components in a motive compartment of the car


The scheme of an arrangement of elements in the assembly block of the relay No. 1

For giving of power supply or a signal of management on some of consumers of the electric power in the car (such as components of system of injection of fuel, a horn, a starter, the cooling system fan(s), fog lights and so forth) relays are used. Actually, the relay represents the electric key providing short circuit of VV of a contour on NV to a signal. In case of a relay exit out of operation there is a refusal of functioning of the corresponding consumer. The most part of the relay is placed in the assembly blocks which are located in assembly blocks in a motive compartment (blocks No. No. 1 and 2 — see the illustration Scheme of an Arrangement of Electric Components in a motive compartment of the car) and in interior of the car (see the illustrations Located in a motive compartment the assembly block of safety locks / relay (No. 2), the Arrangement of two breakers of a chain in the saloon assembly block of safety locks / relay, the Scheme of an arrangement of elements in the assembly block of the relay No. 1). The description of check of serviceability of functioning of the relay is given below. The failed relays are subject to replacement.


Check

If it is not possible to find out a way of turning on of the relay in the corresponding electric contour according to schemes of electric connections, it is necessary to remember that approach to check of any relay in principle is identical in all cases (see further).

In the majority of the relay the contour of management is always connected to two of contact plugs. When giving on these NV plugs of tension current begins to circulate on a winding of management of the relay therefore there is a short circuit of big contacts of a working contour of the consumer of the electric power. Other plugs are plugs of working (VV) of a contour.

For the purpose of simplification of identification of plugs of the relay explanatory marking with the image of the scheme of connection of keys is usually applied on its case (see the schemes given below).


The constructive scheme of the typical 4-contact relay with numbering of plugs and planimetric connections


The constructive scheme of the typical 4-contact relay with numbering of plugs and planimetric connections

 PERFORMANCE ORDER

  1. Connect the wire crossing point equipped with a safety lock between one of plugs of management of the relay and the positive plug of the battery. By means of the second wire crossing point ground the second plug of management — the relay has to publish click. Some relays demand obligatory respect for polarity of connection — if the click did not happen, try to change polarity of connection of plugs of management.
  2. At the connected wires crossing points check existence of conductivity between the contour VV plugs, having connected an ohmmeter according to the key scheme on the relay case.
  3. At negative result of check replace the relay.


"on the page back
12.5. Chain breakers - the general information
on the following page"
12.7. Check of serviceability of functioning and replacement of the breaker of indexes of turns / alarm system




5d7aa768