Service of the Infiniti QX4 since 1996 of release
1. Introduction
2. Maintenance instruction
3. Routine maintenance
4. Engine
5. Cooling system and heating
6. Feed and control systems
7. Systems of start and charge
8. Transmission line
9. Brake system
10. Suspension bracket and steering
10.1. Specifications
10.2. Assessment of the general condition of components of a suspension bracket and steering of the car
10.3. Check of a state and replacement of spherical support of a forward suspension bracket
10.4. Check of a condition of steering drafts
10.5. Removal and installation of the cross lever of a forward suspension bracket
10.6. Adjustment of a pretightness of stupichny bearings of forward wheels
10.7. Removal, check of a state and installation of screw springs and rack-mount assemblies of a forward suspension bracket
10.8. Removal and installation of stupichny assembly and rotary fist
10.9. Removal, check of a state and installation of the forward stabilizer of cross stability
10:10. Replacement of stupichny bearings
10:11. Check of a condition of shock-absorbers and springs of a back suspension bracket
10:12. Removal and installation of components and assembly of a back suspension bracket
10:13. Removal, check of a state and installation of levers of a back suspension bracket
10:14. Removal, check of a state and installation of screw springs of a back suspension bracket
10:15. Removal and installation of shock-absorbers of a back suspension bracket
10:16. Removal and installation of the back stabilizer of cross stability
10:17. Removal, check of a state and installation of a cross jet bar of a back suspension bracket
10:18. Pumping of a hydraulic path of the steering drive
10:19. Checks and adjustments of a steering wheel
10:20. Check of effort of resistance to sliding of a lath of the steering mechanism
10:21. Adjustment of torque of a provorachivaniye of the leading gear wheel of the steering mechanism
10:22. Check of hydraulic pressure of GUR
10:23. Adjustment of effort of a tension of a belt of the drive of the steering pump
10:24. Removal and installation of reduktorny assembly
10:25. Removal and installation of assembly of the steering mechanism
10:26. Removal and installation of the steering pump
10:27. Removal and installation of a steering wheel
10:28. Removal and installation of assembly of the combined understeering switches
10:29. Removal and installation of the lock of ignition / blocking of a steering column
10:30. Removal, check of a state and installation of a steering column
10:31. Angles of installation of forward wheels
11. Body
12. Electric equipment
 






5d7aa768






10-22-proverka-gidravlicheskogo-davleniya-gur.html

10:22. Check of hydraulic pressure of GUR


Check of hydraulic pressure of GUR

Do not block the locking valve of the manometer more than for 15 seconds at the working engine! Do not hold a steering wheel in extreme provisions more than for 15 seconds!


 PERFORMANCE ORDER

    Check serviceability of a condition of a pulley and correctness of adjustment of a belt of the drive of the steering pump (see Adjustment of effort of a tension of a belt of the drive of the steering pump). Modify properly pressure of a rating of tires. Disconnect a hose of the line of a high pressure from the steering pump, establish a transitional nozzle of KV48102500 (J26357-10) between the pump and the steering mechanism, having connected to it the KV48103500/ST27091000 (J26357) manometer (see the illustration Check of Hydraulic Pressure GUR). Completely open the locking valve and remove from system air traffic jams (see Pumping of a hydraulic path of the steering drive). Check the level of hydraulic liquid in the tank of the steering pump, in case of need make the corresponding adjustment. Start the engine on single turns for warming up of the GUR hydraulic liquid up to the temperature of 60 — 80 °C.

The engine has to work at completely open locking valve in order to avoid excessive temperature increase as a result of rise in pressure to the maximum level.

    Lift engine turns to value 1000 in a minute and make measurement of pressure, having quickly turned a steering wheel from an emphasis against the stop in both directions. If as a result of check the maximum nominal rate is reached (see Specifications), therefore, the system functions normally. At excess by result of measurement of the maximum value check serviceability of a condition of the valve of management of a stream of the steering pump. If the indication does not reach the upper bound of admissible range, slowly block the locking valve and repeat check, rise in pressure to the maximum level testifies to malfunction of the steering mechanism, otherwise believe the steering pump — do not block the locking valve longer than for 15 seconds in a row. Disconnect the manometer, remove a nozzle and restore initial connection of hydraulic lines. Pump over a hydraulic path of GUR (see Pumping of a hydraulic path of the steering drive). Check the level of hydraulic liquid, in case of need make the corresponding adjustment.


"on the page back
10:21. Adjustment of torque of a provorachivaniye of the leading gear wheel of the steering mechanism
on the following page"
10:23. Adjustment of effort of a tension of a belt of the drive of the steering pump